HOME > En Linear Unit > En Linear Guide

Products on this page are available only in Asian countries

Linear Guides

The patented shaft slides are perfectly suited for assembling of complex multiple axis systems for handling and machining. 

The wide range of models covers a multitude of applications.

All models can be produced to order with various profile lengths (70, 100, 150 and 200 mm). 


LFS12-10.png

Linear Guide Construction.jpg

Mechanism

  1. Lubrication options to both sides for the recirculating balls.

  2. The basic supports for all linear guides are extruded aluminium profiles compliant with DIN EN 12020-2, which are provided with T-slot inserts for fastening in the body of the profile or with drilled hole fixing points.

  3. Precision steel shafts with a hardness of 60 ± 2 HRC are used as guide rails. All LFS-8 versions are
    optionally available with stainless steel shafts.

  4. The recirculating ball steering systems are glass fibre reinforced.

  5. There are patented recirculating balls in the linear slide. Ball bearings run in each case between two ground steel pins and the guidance shaft.

  6. The slide is adjusted with self-lokking setting screws. This is how the rows of balls and shafts or pins are
    used with each other and thus prestressed. The slide are preset in the factory to the correct stress. All shaft slides are optionally available in a stainless version.

  7. To secure transport loads, slot plates, etc., the shaft slide are provided with T-slot inserts or fixing borings.



LFS 8-1

LFS8-1.png

  • W 30 x H 20 mm (LFS-8-1)
    W 30 x H 32.5 mm (LFS-8-2)
  • 2 precision steel shafts Ø 8
  • Anti-twist lock
  • Aluminium shaft housing profile
  • Special lengths to order
  • Weights: 1.6 kg/m (LFS-8-1)           2.0 kg/m (LFS-8-2)
  • Stainless steel version is available as option


LFS 8-3

LFS8-3.png

  • W 115 x H 25.5 mm
  • 2 precision steel shafts Ø 8
  • Particularly resistant to twisting
  • Aluminium shaft housing profile
  • Special lengths to order
  • Weight: approx. 3.2 kg/m
  • Stainless steel version is available as option


LFS 8-4

LFS8-4.png

  • W 80 x H 80 mm
  • 4 precision steel shafts Ø 8
  • Anti-twist
  • Aluminium shaft housing profiles
  • Special lengths to order
  • Weight: approx. 7.2 kg/m
  • Stainless steel version with 2 steel shafts 2 slide or trolley


LFS 12-2

LFS12-2.png

  • W 62 x H 31 mm
  • 2 precision steel shafts Ø 12
  • Anti-twist lock
  • Aluminium shaft housing profile
  • High parallelism by patented shaft housing
  • High guidance accuracy
  • Max. length up to 2998 mm
  • Special lengths to order
  • Weight: approx. 3.3 kg/m


LFS 12-3

LFS12-3.png

  • W 90 x H 31 mm
  • 2 precision steel shafts Ø 12
  • Anti-twist
  • Aluminium shaft housing profile
  • increased shaft spacing for higher torque absorption
  • Any guide length
  • Weight: approx. 3.9 kg/m


LFS 12-10

LFS12-10.png

  • W 36 x H 24.5 mm
  • 2 precision steel shafts Ø 12
  • Anti-twist
  • Aluminium shaft housing profile
  • Special lengths to order
  • Weight: approx. 2.9 kg/m


LFS 16-120

LFS16-120.png

  • W 190 x H 61 mm
  • 2 precision steel shafts Ø 16
  • Anti-twist
  • Aluminium shaft housing profile
  • Any guide length
  • Weight: 10.2 kg/m










Handling

Installation site

In principal, the installation site for linear guides can be chosen anywhere.
You merely have to consider whether all the forces and moments arising are below the maximum values for the relevant axes.


Temperatures

All linear guides are designed for continuous operation at ambient temperatures of up to 60 °C. In short-term operation, maximum temperatures of 80 °C are permissible.

Linear guides are unsuitable for temperatures below freezing.


Straightness/Warping

The aluminium profiles used are extruded profiles, which exhibit divergences regarding straightness and may be warped, owing to the manufacturing process.

The tolerance of this deviation is set out in DIN EN 12020-2.

In the worst case, the linear guide eviations equal these limits, but typically they are lower.
In order to achieve the desired guidance accuracy, the guide must be aligned using shims or clamped to a bearing service machined to the corresponding accuracy. This achieves tolerances of at least 0.1 mm/1000 mm.


Principles
Load capacity and working life


The dimensioning of a linear guide is based on the load capacity of the individual elements. The load capacity is described by:

  • the dynamic load factor C
  • the static load factor C0
  • the static torques M0X, M0Y and M0Z

The basis of the dynamic load factors according to DIN is a nominal working life of 100,000 m displacement path.
Far East suppliers often quote load factors for a nominal working life of 50,000 m displacement path; this produces
load factor figures which are approximately 20% higher than those according to DIN.

Dynamic load capacity


The fatigue characteristics of the materialdetermine the dynamic load capacity.
The working life - the fatigue period - also depends on:
  • the stress on the linear guide
  • the speed at which
  • the linear guide moves
  • the statistical randomness
  • of the first damage occurring

Useful life


Useful life means the working life actually achieved by a linear guide. The useful life may differ from the computed working life. The following can lead to premature failure through wear or fatigue:
  • Misalignments between guide rails or guidance elements
  • Contamination of the guide rails
  • Insufficient lubrication
  • Oscillating motion with very small lifts (formation of grooves)
  • Vibrations at rest (formation of grooves)
Owing to the multiplicity of installation and operating relationships, it is impossible to determine the useful life of a linear guide exactly in advance.
The safest way to make an accurate estimate of the useful life is, as before, a comparison with similar installations.